Whole-house POE
A final disinfection stage where realistic simultaneous demand stays within the selected model basis.
HIGH-FLOW POE UVC LED SYSTEM · 12 GPM
AGLED-12G 12 GPM Commercial UVC LED Water Sterilizer
A 24 V DC high-flow module for whole-house and light-commercial systems.
AGLED-12G combines a 12 GPM flow class, G1 connection and 24 V DC architecture for whole-house and light-commercial water-treatment projects.
12 GPM Maximum flow · 45 LPM
16 W Rated input power
500 mW UVC radiant output
5,000 h L70 service basis
PRODUCT ROLE
High-flow physical UVC treatment for defined POE conditions.
The model provides a UVC disinfection stage for pretreated whole-house and light-commercial water paths. Filtration, UVT, turbidity, iron, hardness and realistic simultaneous demand remain separate design inputs.
APPLICATION FIT
Match 12 GPM performance to a defined POE duty.
- Flow matching: our application team matches the model to the highest realistic draw and target operating condition
- Water review: we review UVT, turbidity, hardness, iron and the appropriate pretreatment
- Mechanical fit: we align pressure, connection, flow direction, mounting and service clearance
- Electrical fit: we select the suitable supply, appliance controls and flow-activation configuration
- Project documents: we prepare the relevant drawing, model report and market documents for review
Light commercial
Pretreated drinking-water lines with defined peak flow, water quality and duty cycle.
Well-water polishing
Our team matches the model with the water analysis and required sediment, iron or other pretreatment.
OEM high-flow systems
Integration into equipment with confirmed G1 connections, 24 V DC supply and service plan.
ENGINEERING DATA
Specifications for model selection.
The current drawing, datasheet and manual are available for project review. Our team will align them with the quoted configuration.
01
DIMENSION DRAWING AGLED-12G mechanical drawing
Hydraulic & mechanical
Fit the model to the water path.
- Maximum flow rate
- 12 GPM · 45 LPM
- Startup flow
- >4 L/min
- Maximum inlet pressure
- 0.8 MPa
- Water temperature
- 1–45°C
- Inlet / outlet
- G1 female; compatible with 1-inch NPT1 / PT1 / G1 / R1 male thread
- Product envelope
- Ø63.5 × 315 mm drawing basis
- Net / gross weight
- 2.4 kg / 2.6 kg
Electrical & optical
Use the correct powered version.
- Input voltage
- 24 V DC
- Output current
- 600 mA
- Input current
- 0.7 A
- Rated power
- 16 W
- UVC radiant output
- 500 mW
- UVC wavelength
- 270–280 nm
- L70 service basis
- 5,000 hours
- Switch cycles
- >100,000
04
ELECTRICAL & OPTICAL DATA Product parameters
| No. | Parameter | Symbol | Value | Unit |
|---|---|---|---|---|
| 01 | Input voltage | VIN | 24 | V DC |
| 02 | Output current | IOUT | 600 | mA |
| 03 | Input current | IIN | 0.7 | A |
| 04 | Rated power | W | 16 | W |
| 05 | UVC radiant output | Φe | 500 | mW |
| 06 | UVC wavelength | WLP | 270–280 | nm |
| 07 | Lifetime test | L70 | 5,000 | h |
Model-document note
The current AGLED-12G datasheet, drawing and SGS report are available for project review and quotation support.
OEM INTEGRATION REVIEW
Design the module into a complete POE treatment train.
Our application team matches simultaneous draw, pretreatment, UVT, pressure loss, G1 connection, power supply and service access to the complete POE layout.
- 01 Define water conditions
Peak flow, UVT, turbidity, temperature and upstream treatment.
- 02 Match mechanical fit
Pressure, connection size, flow direction, mounting and service clearance.
- 03 Select electrical version
Supply voltage, host-appliance logic, flow activation and safe cable routing.
- 04 Assemble project documents
Match the exact model report and compliance documents to the target project.
MODEL-SPECIFIC EVIDENCE
99.999% SGS-verified E. coli reduction at 12 GPM under the report test conditions.
The linked model report presents the organism, flow and water conditions behind this result; our team aligns them with the project duty.
Open model test reportModel-specific results with clear test conditions.
The report identifies the model, organism, flow and water conditions behind the performance result.
Documents organized by project purpose.
Performance reports and compliance documents are listed independently for straightforward review.
Factory Test Items and Acceptance Criteria.
The table below lists the factory test items and acceptance criteria for the specific model.
The table below lists the factory test items and acceptance criteria for AGLED-12G.
No. Test item Test method and criteria
01 Sealing test
Static pressure is maintained at 0.2 MPa for 5 minutes without air leakage.
02 Pressure resistance
Hydrostatic pressure is increased to 0.6 MPa within 5 minutes at a rate of ≤0.4 MPa/s and held for 15 minutes to check module water tightness.
03 Burst test
Water pressure is raised to 0.8 MPa within 70 seconds at a rate of ≤0.4 MPa/s, held for 5 seconds and released; appearance, mechanical and electrical performance remain normal.
04 Cyclic pressure
100,000 repeated cycles at 0–0.45 MPa with a 2-second pressure rise are used to observe module water tightness.
05 Dry-burning test
The water purification device operates powered on without water for 24 hours; the module remains undamaged and all functions remain available.
06 Low-temperature storage
The sample is stored at −20°C ±2°C for 72 hours and recovered at room temperature for at least 1 hour; appearance remains normal, and UVC intensity and module operating current meet the drawing requirements.
07 High-temperature storage
The sample is stored at 50°C ±2°C for 72 hours and recovered at room temperature for at least 1 hour; appearance remains normal, and UVC intensity and module operating current meet the drawing requirements.
08 Constant temperature and humidity
The module is placed in a 40°C, 85% RH test chamber for 168 hours without damage, and all functions remain available.
09 Vibration test
The packaged product is tested at 4 Hz (240 CPM) for 60 minutes to ISTA-2001; packaging, product surfaces and parts show no obvious damage, and product function remains normal.
10 Salt-spray test
At 35°C ±2°C, 5% NaCl and pH 6.5–7.2, the sample is exposed for 48 hours to GB/T 2423.17, rinsed and recovered; module components show no rust or obvious oxidation.
11 Drop test
Packaging corners, edges and surfaces are dropped freely from a 1-metre platform; packaging, fixtures, product surfaces and parts meet the stated mechanical, electrical and appearance criteria.
12 Hazardous substances
Module hazardous-substance content is checked against the limit requirements of the EU RoHS directive.
DOCUMENT CENTER
Review the technical package for your project.
Drawings, performance reports, installation documents and market files are organized by purpose for easier project review.
PRODUCT AGLED-12G Filter Solution Flyer Model overview and system positioning. MANUAL AGLED-12G Owner's Manual Operation, safety and service information. SGS AGLED-12G SGS Test Report Model performance under the report conditions. CATALOG UVC LED Product Catalog 2026 Series comparison and model context.
APPLICATION REVIEW
Find the right AGLED-12G configuration for your project.
Share your peak flow, water quality and integration requirements. Our application team will match the model, configuration and supporting documents to your project.